Page 9 - La Decor LLC - Quality Incomparable

CERTIFICATION

GUARANTEE

To support the high quality and first-class engineering that has gone into the Dorfit product range, we Certificate of Constancy of Performance
offer a three to five years guarantee (subject to terms and conditions) against defects due to faulty 0359-CPR-000550
manufacturing, workmanship or defective material. We agree to replace any defective Dorfit products In compliance with Regulation 305/2011/EU of the European Parliament and of the
Council of 9 March 2011 (the Construction Products Regulation), this certificate applies
free of charge provided that the product has been fitted in accordance with the fitting instructions and to the construction product(s).
maintained correctly. Product(s): Mechanically operated locks, latches and locking plates
(refer to attached appendix for details and conditions)
Placed on the market LA DECOR LLC.
under the trade mark of: P.O. Box: 41959, Near Baniyas, Metro Station, Deira, Dubai, United Arab
Emirates (U.A.E.)
CARE INSTRUCTIONS Produced in the A017
manufacturing plant(s):
Intended use: When used with an appropriate door closing device on fire and/or smoke control
doors to fulfil the self-closing requirement of such doors, and thereafter to
STAINLESS STEEL ensure that the door remains shut. CE CERTIFICATE
This certificate attests that all provisions concerning the assessment and
verification of constancy of performance described in Annex ZA of the
Routine cleaning is necessary for maximum corrosion resistance and to preserve the appearance of the standard(s):
EN 12209:2003/AC:2005
surface through many years of daily use. Exposed surfaces should be cleaned with a mild detergent in Under system 1 for the performance set out in this certificate are applied and
warm water, applied with a soft cloth or synthetic sponge. Rinse in hot water and dry with a soft cloth that the performance of the construction product is assessed to remain
constant.
or allow to ‘drip’ dry. Routine cleaning applied over several days will generally remove heavy soiling and This certificate was first issued on 31 st May 2017 under CPR (305/2011) and
will remain valid as long as neither the harmonised standard, the construction
product, the AVCP methods nor the manufacturing conditions in the plant are
staining. Do not use course abrasive powders, metallic scourers, silver or brass cleaners, or acid-based modified significantly, unless suspended or withdrawn by the notified product
certification body.
cleaning materials. The issued document and statement(s) herein makes reference only to a presumption
of conformity in accordance with the CPR Regulations EU 305/2011 (as amended).
However, it is the manufacturer’s or their authorised representative’s sole responsibility
BRASS to affix the CE logo and, by doing so, confirms full compliance and conformity to all
other European mandatory directives and regulations that may also apply.
0359
Clean the surface using a soft cloth with soapy water. Alternatively, you may also use isopropyl (rubbing
alcohol) applied with a soft sponge. After cleaning, wipe the surface thoroughly with a clean and dry soft
Intertek Testing & Certification Limited Date 31 May-2017 8/3/2017 GWZQ.R38981 - Door Hinges
rag. For polishing the brass surface, use “yellow” treated dust cloth. Wipe down the brass surface with this Cleeve Road, Leatherhead Issue 01
Surrey, KT22 7SB
Tel: + 44 (0)1372 370900
cloth and then buff it dry with a soft, cotton cloth. This trace amount of oil in the cloth should not smear or Fax: +44 (0)1372 370977 GWZQ.R38981
E-mail: cpd.uk@intertek.com
David Bigland Certification Manager Door Hinges
discolor, especially after buffing. www.intertek.com Registered No 3272281 Academy Place, 1-9 Brook Street, Brentwood, Essex, Page Bottom
CM14 5NQ, United Kingdom
This Certificate is for the exclusive use of Intertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility
and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with Door Hinges
the agreement, for any loss, expense or damage occasioned by the use of this Certificate. Only the Client is authorized to permit copying or distribution of
this Certificate and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or
KEY TO SYMBOLS Page 1 of 4 See General Information for Door Hinges
service must first be approved in writing by Intertek.
LA DECOR LLC
Near Baniyas Metro Station R38981
Deira
Dubai, United Arab Emirates 41959 UNITED ARAB EMIRATES
Suitable to meet the needs of disabled people. Stainless steel ball bearing type hinges, Models: DTBB433/SS304, DTBB43.53/SS304, DTBB443/SS304, DTBB4.543/SS304,
DTBB4.543.4/SS304, DTBB4.54.53/SS304, DTBB4.54.53.4/SS304, DTBB4.544.6/SS304, DTBB4.54.54.6/SS304, for use on swinging
type fire doors rated up to and including 3 hours.
Last Updated on 2016-12-03
Questions? Print this page Terms of Use Page Top
© 2017 UL LLC
Suitable for use on fire doors. The appearance of a company's name or product in this database does not in itself assure that products so identified have been
manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Certified and
covered under UL's Follow-Up Service. Always look for the Mark on the product.
UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1.
The Guide Information, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) must be presented in their
entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from
the Online Certifications Directory with permission from UL" must appear adjacent to the extracted material. In addition, the
CE Marking is a certification to the highest levels of attestation required by the construction reprinted material must include a copyright notice in the following format: "© 2017 UL LLC".
products directive. The CE mark indicates that the product has undergone rigorous testing UL CERTIFICATE
and is in accordance with the industry requirements.
EN12209 is the British/European standard requirement for locks, latches and locking plates.
3 years mechanical guarantee.
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name=GWZQ.R38981&ccnshorttitle=Door+Hinges&objid=1086285417&cfgid=1… 1/1
5 years mechanical guarantee.

8 Designer HARDWARES www.dorfit.co.uk Designer HARDWARES www.dorfit.co.uk 9